Official PayPal Seal
Morris 96114 Above Ground Insulation Piercing Connectors Main 4/0-2 Tap 4/0-4

Morris 96114 Above Ground Insulation Piercing Connectors Main 4/0-2 Tap 4/0-4

Your Price: $26.73
Part Number

:MOR_96114
Morris 96114 Above Ground Insulation Piercing Connectors Main 4/0-2 Tap 4/0-4
 
Above Ground Insulation Piercing Connectors Main 4/0-2 Tap 4/0-4 - Anyone can use our Above Ground Connector

Above Ground Insulation Piercing Connectors Main 4/0-2 Tap 4/0-4 features include:

  • Connector Installs In Just Minutes Saving Many Man-Hours On The Job
  • Eliminates Wire Stripping, Connecting & Taping of Split Bolts and Adding Inhibitor
  • Above ground connector can be installed on Energized Circuits eliminating Power Shutdowns
  • Overhead services - both insulated & bare mains, above grade URD services, street lighting, non-tension splicing & tapping, insulated replacement for split bolts, tapping without cutting the main, gutter taps.
  • Double shear-head bolt guarantees correct torque tightening every time, ensuring a quality connection, & eliminating the possibility of hot spots, damaged wires or loose connections
  • No cable stripping required, simply insert the jacketed cable into the entry port & tighten with a 1/2” 6 point socket
  • Red Turbo spacer allows tap side to remain open while you hand tighten the above ground connector on the main wire (all models except 96102 & 96104)
  • Blue Rubber Insert recreates insulation when used on bare wire. Used to avoid any damage on neutral messenger. (Only on Models 96106, 96110, 96112, 96114)
  • The bolt and all external parts of the connector are completely isolated from energized parts and the bolt is covered by the plastic shear-head.  The installer has no contact at any point with an energized part.
  • Can be installed on energized conductors, however, the tap must not be under load.
  • Corrosion-free connection is good for hot, cold, damp, & salty connections.  Properly installed the connector seals water-tight. This is accomplished by a sealant tank, that during installation is compressed and forces sealant out to protect the connection from oxygen and water.  Copper teeth are tin plated, shell is high strength UV resistant thermoplastic insulating material, steel bolts are galvanized.
  • The connector bodies are made from high-strength fiber-reinforced thermoplastic and galvanized steel bolts
  • UL486B Listed for cu to cu, al to al, & cu to al; 600 Volt, 194°F (90°C) Rated, Meets ANSI C119.4 requirements
  • Order Qty of 1 = 1 Piece

Below is more info on our Above Ground Insulation Piercing Connectors Main 4/0-2 Tap 4/0-4

 
Features:
  • Above Ground Insulation Piercing Connectors - Anyone can use our Above Ground Connector
  • Connector Installs In Just Minutes Saving Many Man-Hours On The Job
  • Eliminates Wire Stripping, Connecting & Taping of Split Bolts and Adding Inhibitor
  • Above ground connector can be installed on Energized Circuits eliminating Power Shutdowns
  • Overhead services - both insulated & bare mains, above grade URD services, street lighting, non-tension splicing & tapping, insulated replacement for split bolts, tapping without cutting the main, gutter taps
  • Double shear-head bolt guarantees correct torque tightening every time, ensuring a quality connection, & eliminating the possibility of hot spots, damaged wires or loose connections
  • No cable stripping required, simply insert the jacketed cable into the entry port & tighten with a 1/2" 6 point socket
  • Red Turbo spacer allows tap side to remain open while you hand tighten the above ground connector on the main wire (all models except 96102 & 96104)
  • Blue Rubber Insert recreates insulation when used on bare wire. Used to avoid any damage on neutral messenger. (Only on Models 96106, 96110, 96112, 96114)
  • The bolt and all external parts of the connector are completely isolated from energized parts and the bolt is covered by the plastic shear-head. The installer has no contact at any point with an energized part
  • Can be installed on energized conductors, however, the tap must not be under load
  • Corrosion-free connection is good for hot, cold, damp, & salty connections. Properly installed the connector seals water-tight. This is accomplished by a sealant tank, that during installation is compressed and forces sealant out to protect the connection from oxygen and water. Copper teeth are tin plated, shell is high strength UV resistant thermoplastic insulating material, steel bolts are galvanized
  • The connector bodies are made from high-strength fiber-reinforced thermoplastic and galvanized steel bolts
  • UL486B Listed for cu to cu, al to al, & cu to al; 600 Volt, 194 Degrees F (90 Degrees C) Rated, Meets ANSI C119.4 requirements
  • Model #'s: 96102 (TTD0510F), 96104 (TTD0810F), 96106 (TTD1010FBTUNI), 96108 (TTD1510FT), 96110 (TTD1810XFBTUNI), 96112 (TTD2110FBTUNI), 96114 (TTD2710FBTUNI), 96116 (TTD4010FBT), 96118 (TTD4310FBT), 96120 (TTD4510FT), 96122 (TTD5510FBT)
  • Double shear-head bolt guarantees correct torque tightening every time, ensuring a quality connection, & eliminating the possibility of hot spots, damaged wires or loose connections. No cable stripping required, simply insert the jacketed cable into the entry port & tighten with a 1/2" 6 point socket. Red Turbo spacer allows tap side to remain open while you hand tighten the above ground connector on the main wire (all models except 96102 & 96104). Blue Rubber Insert recreates insulation when used on bare wire. Used to avoid any damage on neutral messenger. (Only on Models 96106, 96110, 96112, 96114). The bolt and all external parts of the connector are completely isolated from energized parts and the bolt is covered by the plastic shear-head. The installer has no contact at any point with an energized part. Can be installed on energized conductors, however, the tap must not be under load. Corrosion-free connection is good for hot, cold, damp, & salty connections. Properly installed the connector seals water-tight. This is accomplished by a sealant tank, that during installation is compressed and forces sealant out to protect the connection from oxygen and water. Copper teeth are tin plated, shell is high strength UV resistant thermoplastic insulating material, steel bolts are galvanized. The connector bodies are made from high-strength fiber-reinforced thermoplastic and galvanized steel bolts. UL486B Listed for cu to cu, al to al, & cu to al; 600 Volt, 194 Degrees F (90 Degrees C) Rated, Meets ANSI C119.4 requirements. Model #'s: 96102 (TTD0510F), 96104 (TTD0810F), 96106 (TTD1010FBTUNI), 96108 (TTD1510FT), 96110 (TTD1810XFBTUNI), 96112 (TTD2110FBTUNI), 96114 (TTD2710FBTUNI), 96116 (TTD4010FBT), 96118 (TTD4310FBT), 96120 (TTD4510FT), 96122 (TTD5510FBT). .
 
Specifications:
  • Wire Size: 4/0-4
  • Color: Black
  • Insulation Type: Fiberglass Reinforced Thermoplastic
  • Maximum Voltage: 600
  • Temperature Rating: 194 oF 90oC
  • Material: Copper
  • UL Listing: UL
  • Mfg Standard: ANSI C119.4 Compliant
  • Mfg Standard: ANSI C119.4 Compliant
  • Mfg Standard: ANSI C119.4 Compliant
  • Mfg Standard: ANSI C119.4 Compliant
  • Mfg Standard: ANSI C119.4 Compliant
  • Mfg Standard: ANSI C119.4 Compliant
  • Mfg Standard: ANSI C119.4 Compliant
  • Mfg Standard: ANSI C119.4 Compliant
  • Mfg Standard: ANSI C119.4 Compliant
  • Mfg Standard: ANSI C119.4 Compliant
  • Mfg Standard: ANSI C119.4 Compliant
  • Mfg Standard: ANSI C119.4 Compliant
  • Mfg Standard: ANSI C119.4 Compliant
  • Direct Burial Rating: UL 467 Listed For Direct Burial & Grounding/Bonding Applications
  • Country of origin: France
Catalog 1   

Recently Viewed Items